CONTACTLESS TACHOMETER PDF

Contactless tachometer using pic microcontroller: Contactless digital tachometer project is designed to measure speed of dc motor using PIC18F46K Simple but accurate digital tachometer using microcontroller Has a resolution of 1 rev/sec. The tachometer use an optical pickup scheme for picking . Buy Digital Photo Laser Tachometer Non Contact Tach RPM Meter: Tachometers – ✓ FREE DELIVERY possible on eligible purchases.

Author: Faegami Zunos
Country: Myanmar
Language: English (Spanish)
Genre: Travel
Published (Last): 14 March 2005
Pages: 202
PDF File Size: 10.35 Mb
ePub File Size: 10.16 Mb
ISBN: 609-9-31595-266-9
Downloads: 84405
Price: Free* [*Free Regsitration Required]
Uploader: Mijora

For the price, its a steal because lab grade or highly accurate tachometers are VERY expensive. You may also like: The interrupt counts the number of times the voltage variation occurs in the resistor in series with the receiver and sends the value to the LCD display every second. Showing of reviews. The photo transistor conducts more at this moment and as a result the voltage across R3 68K resistor shoots up coontactless this moment.

There is not much to say after that. It has a simple red laser that reflects nicely off the included tape. It can measure RPS speed up to the desired value, dontactless on the speed of the motor. There was a problem filtering reviews right now. Please try again later. Amazon Music Stream millions of songs. The result will be a waveform like what shown below at the emitter of the photo transistor. The LED and the buzzer connect to the microcontroller which monitors the speed of the motor.

Hence we clntactless get an alert whenever the speed of the motor goes above a fixed value. cohtactless

Also, there is a change in the sensor circuit. The output is given in rpm revolutions per minute and the number of digits are increased from 3 to 5. It works on the principle that the number of times the IR receiver-transmitter circuit is cut and re-established in a second gives the number of rotations per second. The program actually counts the number of negative going pulses in 1. Hae there,i want to make the tracometer but a few things are troubling me.

  CDSCO GCP GUIDELINES PDF

Receiver coverts this received radiations to a corresponding electric current. So knowing about ocntactless speed of a machine is inevitable in order to calculate or control the speed. Earlier tachometers purely mechanical where the revolution is transferred to the tachometer through mechanical coupling cable or shaftthe rpm is determined using a gear mechanism and it is displayed on a dial. It looked like the portion where the laser dot is generated within the unit had shifted in mfg.

You can use any single supply opamp that matches our supply voltage 5V. I use an In system programmer ISP module for programming the I returned this unit without any tachometsr as the laser dot was cut off at the upper side of the round laser dot by percent. For sending the light across directly max distance is about 10m or more with a very high sensitivity photo detector and high intensity IR LED.

It was easy enough to figure an average. With the advent of modern electronics, the tachometers have changed a lot.

: Digital Photo Laser Tachometer Non Contact Tach RPM Meter: Automotive

Full program for the digital tachometer using arduino is shown below. I have a problem in the optical pick up assembly. Previous post Next post. For warranty information about this product, please click here.

Add both to Cart Add both to List.

Design of a Contactless tachometer | Open Access Journals

It can measure time interval with better accuracy. Tachometer is a device used for measuring the number of revolutions of an object in a given interval of time. The circuit diagram of the LCD tachometer using is given below. Sold by CyberTech and Fulfilled by Amazon.

  BLOOD WITCH BY CATE TIERNAN PDF

Technical Details

The circuit of our paper was designed and implemented. I pointed it at a roll of masking tape sitting on my bench and it said it was spinning RPM. I needed a photo tach to determine gear ratios in an old sealed transmission, this thing worked perfect.

Such a setup needs a variable potentiometer to be connected across the supply of the motor and thereby the speed of the motor can be varied to an extent. The Microcontroller is programmed such that when the output of the counter attains a value above a fixed value in this paper the value is fixed at 29 rpsit sends a high signal to its MSB 7th pin of port C which is connected in series with an LED and a buzzer.

The instruction CPL A will just complement the digit drive pattern in accumulator so that it becomes suitable for the common anode display. There’s a problem loading this menu right now. If you had something with lights, or lots of reflective surfaces, it could be very misleading, or if you had a chrome device motor, pulley, whatever.

You have to give it a moment for the reading to settle down, but you’ll get an accurate speed when you do. The reflective tape stuck well to the cardboard and I was able to get my rpms and my carb set. Have one to sell?

A provision for controlling the motor vontactless using a potentiometer is also included in the circuit. Pages with related products.